change time MAZDA MODEL 6 2017 Owners Manual (in English)

A Word to Mazda Owners
Thank you for choosing a Mazda. We at Mazda design and build vehicles with complete
customer satisfaction in mind.
To help ensure enjoyable and trouble-free operation of your Mazda, read t\
his manual
carefully and follow its recommendations.
An Authorized Mazda Dealer knows your vehicle best. So when maintenance or \
service is
necessary, that's the place to go.
Our nationwide network of Mazda professionals is dedicated to providing \
you with the best
possible service.
We assure you that all of us at Mazda have an ongoing interest in your mo\
toring pleasure
and in your full satisfaction with your Mazda product.Mazda Motor CorporationHIROSHIMA, JAPAN
Important Notes About This Manual
Keep this manual in the glove compartment as a handy reference for the s\
afe and enjoyable use of your Mazda.
Should you resell the vehicle, leave this manual with it for the next ow\
ner.
All specifications and descriptions are accurate at the time of printing. Because improvement is a constant goal at
Mazda, we reserve the right to make changes in specifications at any time without notice and without obligation.
Air-Conditioning and the Environment
Your Mazda's genuine air conditioner is filled with a refrigerant that has been found not to damage the earth's
ozone layer. If the air conditioner does not operate properly, consult an Authorized Mazda Dealer.
Perchlorate
Certain components of this vehicle such as [air bag modules, seat belt p\
retensioners, lithium batteries,…] may
contain Perchlorate Material-- Special handling may apply for service or\
vehicle end of life disposal. See
www.dtsc.ca.gov/hazardouswaste/perchlorate.
Please be aware that this manual applies to all models, equipment and options. As a result, you may find
some explanations for equipment not installed on your vehicle.
©2016 Mazda Motor Corporation July 2016 (Print2)
Mazda6_8FH2-EA-16F_Edition2.indb 32016/07/07 13:44:05

2–7
Essential Safety Equipment
Seats
*Some models.
Seat Warmer*
The front seats are electrically heated. The
ignition must be switched ON.
Press the seat warmer switch while the
ignition is switched ON to operate the seat
warmer. The indicator lights turn on to
indicate that the seat warmer is operating.
The mode changes as follows each time
the seat warmer switch is pressed.
Front
OFF
High Mid
Lo w
Rear*
OFF
High Mid
Lo w
WARNING
Be careful when using the seat warmer:
The heat from the seat warmer may be
too hot for some people, as indicated
as follows, and could cause a low-
temperature burn.
 Infants, small children, elderly
people, and physically challenged
people
 People with delicate skin People who are excessively fatigued People who are intoxicated People who have taken sleep-
inducing medicine such as sleeping
pills or cold medicine
Do not use the seat warmer with
anything having high moisture-
retention ability such as a blanket or
cushion on the seat: The seat may be heated excessively
and cause a low-temperature burn.
Do not use the seat warmer even when
taking a short nap in the vehicle: The seat may be heated excessively
and cause a low-temperature burn.
Do not place heavy objects with sharp
projections on the seat, or insert
needles or pins into it: This could cause the seat to become
excessively heated and result in injury
from a minor burn.
Mazda6_8FH2-EA-16F_Edition2.indb 72016/07/07 13:44:10

2–9
Essential Safety Equipment
Seats
NOTE
 Individual seat positions can be
programmed to the two available
programming buttons on the side of the
driver's seat, plus one seat position for
each registered key.
 If the vehicle has been serviced and
the battery cables disconnected, the
programmed seat positions will have
been erased. Re-program the seat
positions.
Programming
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Adjust the seat and the active driving
display to the desired driving position.
5. Press the SET button on the seat until a
beep sound is heard one time.
6. Perform one of the following settings
within 5 seconds of completing step 5
above:
 Programming using a button on
the side of the seat
Press the button you want to program,
either button 1 or 2, until a beep
sound is heard one time.
 Programming using the key
Press the key
button until a beep
sound is heard one time.
NOTE
If a beep sound is heard three times, the
operation is canceled.
To move the driving position to a
programmed position
(Using a button on the side of the seat)
1. Make sure the parking brake is on.
2. (Automatic transaxle)
Make sure the selector lever is in the P
position.
3. Start the engine.
4. Press the programming button for the
driving position you want to call up
(button 1 or 2).
5. A beep sound is heard when the driving
position adjustment is completed.
NOTE
 If the driving position movement is not
changed, only the beep sounds.
 A seat position can be called up even
with the engine not running.
 The driving position adjustment is
canceled in the following cases:
 Any of the seat adjustment switches
is operated.
 The SET button is pressed. Programming button 1 or 2 is
pressed.
 The key button or button is
operated.
 The vehicle starts moving. The active driving display is
adjusted.
Mazda6_8FH2-EA-16F_Edition2.indb 92016/07/07 13:44:11

3–5
Before Driving
Keys
Transmitter
Operation buttons
Operation indicator light
NOTE
 (With theft-deterrent system)
The hazard warning lights flash when
the theft-deterrent system is armed or
turned off.
Refer to Theft-Deterrent System on page
3-42.
 (With the advanced keyless function)
A beep sound can be heard for
confirmation when the doors are locked/
unlocked using the key. If you prefer, the
beep sound can be turned off.
The volume of the beep sound can also
be changed.
Refer to Personalization Features on
page 9-10.
Use the following procedure to change
the setting.
1. Switch the ignition off and close all
of the doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.

All of the doors lock and the beep
sound activates at the currently set
volume. The setting changes each time
the LOCK button on the key is pressed
and the beep sound activates at the set
volume. (If the beep sound has been
set to not activate, it will not activate.)
4. The setting change is completed by
doing any one of the following:
 Switching the ignition to ACC or
ON.
 Closing the driver's door. Opening the trunk lid. Not operating the key for 10
seconds.
 Pressing any button except the
LOCK button on the key.
 Pressing a request switch.
Mazda6_8FH2-EA-16F_Edition2.indb 52016/07/07 13:44:22

3–7
Before Driving
Keys
NOTE
 The system can be set to unlock all
doors by performing a single operation.
Refer to Personalization Features on
page 9-10.
Use the following procedure to change
the setting.
1. Switch the ignition off and close all
of the doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
UNLOCK button on the key for 5
seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the
setting each time the UNLOCK
button is pressed (the sound of the
doors locking/unlocking can be
heard).
4. The setting change is completed by
doing any one of the following:
 Switching the ignition to ACC or
ON.
 Closing the driver's door. Opening the trunk lid. Not operating the key for 10
seconds.
 Pressing any button except the
UNLOCK button on the key.
 Pressing a request switch.
 (Auto re-lock function)
After unlocking with the key, all doors
will automatically lock if any of the
following operations are not performed
within about 60 seconds. If your
vehicle has a theft-deterrent system,
the hazard warning lights will flash for
confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalization Features on
page 9-10.
 A door or the trunk lid is opened. The ignition is switched to any
position other than off.
 (With theft-deterrent system)
When the doors are unlocked by
pressing the unlock button on the key
while the theft-deterrent system is
turned off, the hazard warning lights
will flash twice to indicate that the
system is turned off.
Trunk button
To open the trunk lid, press and hold the
trunk button until the trunk lid opens.
Mazda6_8FH2-EA-16F_Edition2.indb 72016/07/07 13:44:22

3–15
Before Driving
Doors and Locks
NOTE
 The system can be set to unlock all
doors by performing a single operation.
Refer to Personalization Features on
page 9-10.
Use the following procedure to change
the setting.
1. Switch the ignition off and close all
of the doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
UNLOCK button on the key for 5
seconds or longer (the sound of
the doors locking/unlocking can be
heard).
After this, the system switches the
setting of pressing the driver's
request switch once or twice
to unlock all doors each time
the UNLOCK button is pressed
(the sound of the doors locking/
unlocking can be heard).
4. The setting change is completed by
doing any one of the following:
 Switching the ignition to ACC or
ON.
 Closing the driver's door. Opening the trunk lid. Not operating the key for 10
seconds.
 Pressing any button except the
UNLOCK button on the key.
 Pressing a request switch.
 Confirm that all doors are securely
locked.
For the trunk lid, move it without
pressing the electric trunk lid opener to
verify that the trunk lid has not been left
ajar.
 All doors cannot be locked when any
door is open.
 It may require a few seconds for the
doors to unlock after the request switch
is pressed.
 A beep sound is heard for confirmation
when the doors are locked/unlocked
using the request switch. If you prefer,
the beep sound can be turned off.
The volume of the beep sound can also
be changed. Refer to Personalization
Features on page 9-10.
Use the following procedure to change
the setting.
1. Switch the ignition off and close all
of the doors and the trunk lid.
2. Open the driver's door.
3. Within 30 seconds of opening the
driver's door, press and hold the
LOCK button on the key for 5
seconds or longer.
All of the doors lock and the beep
sound activates at the currently set
volume. The setting changes each
time the LOCK button on the key is
pressed and the beep sound activates
at the set volume. (If the beep sound
has been set to not activate, it will
not activate.)
4. The setting change is completed by
doing any one of the following:
 Switching the ignition to ACC or
ON.
 Closing the driver's door. Opening the trunk lid. Not operating the key for 10
seconds.
 Pressing any button except the
LOCK button on the key.
 Pressing a request switch.
Mazda6_8FH2-EA-16F_Edition2.indb 152016/07/07 13:44:23

3–16
Before Driving
Doors and Locks
 (With theft-deterrent system)
The hazard warning lights flash when
the theft-deterrent system is armed or
turned off.
Refer to Theft-Deterrent System on page
3-42.
 The setting can be changed so that the
doors are locked automatically without
pressing the request switch.
Refer to Personalization Features on
page 9-10.
(Auto-lock function)
A beep sound is heard when all doors are
closed while the advanced key is being
carried. All doors are locked automatically
after about three seconds when the
advanced key is out of the operational
range. Also, the hazard warning lights
flash once. (Even if the driver is in the
operational range, all doors are locked
automatically after about 30 seconds.)
If you are out of the operational range
before the doors and the trunk lid are
completely closed or another key is left in
the vehicle, the auto-lock function will not
work. Always make sure that all doors and
the trunk lid are closed and locked before
leaving the vehicle. The auto-lock function
does not close the power windows.
 Auto re-lock function
After unlocking with the request switch,
all doors will automatically lock if any
of the following operations are not
performed within about 30 seconds.
If your vehicle has a theft-deterrent
system, the hazard warning lights will
flash for confirmation.
The time required for the doors to lock
automatically can be changed.
Refer to Personalization Features on
page 9-10.
 Opening a door or the trunk lid. Switching the ignition to any position
other than off.
Locking, Unlocking with
Transmitter
All doors can be locked/unlocked by
operating the keyless entry system
transmitter, refer to Keyless Entry System
(page 3-3).
Locking, Unlocking with Door-
Lock Switch
All doors lock automatically when the
lock side is pressed. They unlock when the
unlock side is pressed.
Driver's door
Unlock
Lock
Front passenger's door
Unlock Lock
To lock all the doors from an open front
door, press the lock side of the door lock
switch and then close the door.
Mazda6_8FH2-EA-16F_Edition2.indb 162016/07/07 13:44:24

3–17
Before Driving
Doors and Locks
NOTE
When locking the doors this way, be
careful not to leave the key inside the
vehicle.
Auto Lock/Unlock Function
WARNING
Do not pull the inner handle on a front
door:
Pulling the inner handle on a front
door while the vehicle is moving
is dangerous. Passengers can fall
out of the vehicle if the door opens
accidentally , which could result in
death or serious injury.
 When the vehicle speed exceeds
20 km/h (12 mph), all doors lock
automatically.
 When the ignition is switched off, all
doors unlock automatically.
These functions can also be disabled so
that they do not operate.
Auto lock/unlock function setting
change using door-lock switch
The doors can be set to lock or unlock
automatically by selecting any one of the
functions from the following table and
using the driver's door-lock switch on the
interior door panel.
NOTE
 Function number 3 in the following
table is the factory setting for your
vehicle.
 There are only a total of six auto lock/
unlock settings available for automatic
transaxle vehicles, and three for manual
transaxle vehicles. Be sure to press the
unlock side of the driver's door-lock
switch the correct number of times
according to the selected function
number. If the switch is mistakenly
pressed seven times on an automatic
transaxle vehicle or four times on a
manual transaxle, the procedure will
be cancelled. If this occurs, start the
procedure from the beginning.
Function
number Function*1
1The auto door-lock function is
disabled.
2 All the doors lock automatically when
the vehicle speed is about 20 km/h (12
mph) or more.
3 (Factory Setting) All the doors lock automatically when
the vehicle speed is about 20 km/h (12
mph) or more. All the doors unlock
when the ignition is switched from
ON to Off.
4 (Automatic transaxle vehicles only)
When the ignition is switched ON and
the selector lever is shifted from park
(P) to any other gear position, all the
doors lock automatically.
5 (Automatic transaxle vehicles only)
When the ignition is switched ON and
the selector lever is shifted from park
(P) to any other gear position, all the
doors lock automatically.
When the selector lever is shifted
to park (P) while the ignition is
switched ON, all the doors unlock
automatically.
Mazda6_8FH2-EA-16F_Edition2.indb 172016/07/07 13:44:24

3–18
Before Driving
Doors and Locks
Function number Function*1
6(Automatic transaxle vehicles only)
All the doors lock automatically when
the vehicle speed is about 20 km/h (12
mph) or more.
When the selector lever is shifted
to park (P) while the ignition is
switched ON, all the doors unlock
automatically.
*1 Other settings for the auto door lock function are
available at an Authorized Mazda Dealer. For
details consult an Authorized Mazda Dealer. Refer
to Personalization Features on page 9-10.
Settings can be changed using the
following procedure.
1. Safely park the vehicle. All doors must
remain closed.
2. Switch the ignition ON.
3. Press and hold the lock side of the
driver's door-lock switch within 20
seconds of switching the ignition ON,
and make sure a beep sound is heard
about eight seconds afterwards.
4. Refer to the auto lock/unlock function
setting table, determine the function
number for the desired setting. Press
the unlock side of the driver's door-lock
switch the same number of times as the
selected function number (Ex. If you
select function 2, press the unlock side
of the switch only 2 times).
5. Three seconds after the function setting
has been changed, a beep sound will
beep in the amount of the selected
function number. (Ex. Function number
3 = 3 beep sounds) (Manual transaxle vehicles)
Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Function Number 3
Press 4 times
Press unlock side of
lock switch once
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
W
ait for 3 second
(Automatic transaxle vehicles)
Press unlock side of
lock switch once
Press 2 times
Press 3 times
Current Function Number
Function Number 1
Function Number 2
Press 4 times
Function Number 3
Press 5 times
Function Number 4
Press 7 times
Function Number 5
Press 6 times
Function Number 6
Cancel setting Cancel setting
Function set (The
number of beeps
heard is the same as
the selected function
number)
Press lock side of
lock switch
W ait for 3 second
Mazda6_8FH2-EA-16F_Edition2.indb 182016/07/07 13:44:24

4–18
When Driving
Instrument Cluster and Display
Function for cancelling illumination
dimmer
The illumination dimmer can be canceled
by rotating the dashboard illumination
knob to the right until a beep sound is
heard while the instrument cluster is
dimmed with the ignition switched ON.
If the instrument cluster's visibility is
reduced due to glare from surrounding
brightness, cancel the illumination
dimmer.
NOTE
 (With Multi-information Display)
The illumination dimmer can be
canceled by pressing the dashboard
illumination knob.
 When the illumination dimmer is
canceled, the instrument cluster cannot
be dimmed even if the position lights are
turned on.
 When the illumination dimmer is
canceled, the screen in the center
display switches to constant display of
the daytime screen.
Outside Temperature Display
(Without Multi-information
Display)
When the ignition is switched ON, the
outside temperature is displayed.
NOTE
Under the following conditions, the
outside temperature display may differ
from the actual outside temperature
depending on the surroundings and vehicle
conditions:
 Significantly cold or hot temperatures. Sudden changes in outside temperature. The vehicle is parked. The vehicle is driven at low speeds.
Changing the Temperature Unit of the
Outside Temperature Display
The outside temperature unit can be
switched between Celsius and Fahrenheit.
Settings can be changed by operating the
center display screen.
Refer to Personalization Features on page
9-10.
NOTE
When the temperature unit indicated in the
outside temperature display is changed,
the temperature unit indicated in the
engine coolant gauge display changes in
conjunction with it.
Mazda6_8FH2-EA-16F_Edition2.indb 182016/07/07 13:44:36